Option Industrial LoRaWAN Micro Gateway

Registration and Configuration

If you have not done so already you will need to register your Base Station through your Developer or RAN Provider account using the steps below.

This page shows examples from a CM0125 model Base Station running firmware v2.97.2.

Prerequisites and Registration Information

Verify the Base Station is operating with firmware v2.96.0 or newer.

Note

Firmware updates can scheduled using CloudGate Universe after registering the Base Station.

Verify the Base Station has a LoRa expansion card installed.

The Serial Number ('SNR'), and 'LAN MAC Address' values can be found on the label located on the back of the Base Station.

Screenshot

Note

To obtain the Manufacturer (Base Station) EUI from the listed 'LAN MAC Address' value do the following:

Step	Instruction	Example
1.	Note the listed 'MAC' value.	000CE3759BD8
2.	Insert characters 'FFFE' in-between the 6th and 7th characters from the left.	000CE3 FFFE 759BD8
3.	Ensure there are no spaces and verify your final value has a length of 16 characters.	000CE3FFFE759BD8

Registration on the Senet network

Once the Manufacturer (Base Station) EUI and Base Station SN have been acquired, return to the Senet Portal and complete Registration.

Note

Users with a free Developer Account can find supplemental information using the following link: Generic Developer Gateway Registration
Users registered as RAN Providers can find supplemental information using the following link: Generic RAN Provider Gateway Registration

Using any user account type with access to Base Station registration capabilities; when asked to Select Base Station Type during registration on the Senet Portal, choose the Semtech Basic Station option from the drop down menu.

Screenshot

Enter the unique SN and Manufacturer EUI as required.

Screenshot

Complete the registration process by filling in the remaining fields.

Note

The Base Station supports a maximum of 8 channels at any given time. During registration you will have a chance to select which sub-band of 8 RX Channels the Base Station should operate on to start.

Tip: After registration is complete, you can use the Senet Portal to reconfigure the RX Channel sub-band without the need to login to the Option Access web UI (make sure to power cycle the Base Station after making any changes).

Option Access Web UI Initial Access Instructions

The Base Station is configured by default to host a static wired (Ethernet) address for configuration.

Note

For more information, please refer to the Base Station Quick Start Guide

Ethernet Initial Access Instructions

Ensure all antennas that shipped with the Base Station are installed.
Power on Base Station using the included DC adapter.
Connect an Ethernet cable to the CloudGate’s LAN port on one end and a computer on the other end.
Using the access information below, access the Base Station in a web browser.
Tip: Don't forget to switch back later to the WAN port if the Ethernet interface is configured for backhaul!

Interface	Port	Default Static IP	Default Username	Default Password
Wired (Ethernet)	LAN	192.168.1.1	admin	admin

After logging in, as a security precaution it's strongly recommended to change the default password.

Configuring LoRaWAN Packet Forwarder as a Semtech Basic Station

Verify the Base Station has a valid network backhaul and the Registration process is completed in the Senet Portal.

Warning

Verify that a Static DNS nameserver has been set to avoid connection issues in the next step.

Return to the Option Web UI to configure the Base Station packet forwarding software.
Select Basic Station from the Plugins drop down menu.

Screenshot

Senet LNS URI

The Senet LNS protocol can be configured in two different ways:
1. Secured (Recommended)
2. Unsecured (Debugging and development purposes)

Note

Additional information regarding Basic Station can be found at the following link: Generic Semtech Basic Station

Secured LNS URI (Recommended)

A page will appear showing Basic Station Configuration
Select LNS from the Authentication drop-down menu.
Select 915 (US, AU, AS) from the Region drop-down menu.
Enter the Manufacturer (Base Station) EUI as derived above as the EUI prefix
Enter wss://ns-gw.senetco.io:6042 as the Server URI value.
A copy of the Senet Server Certificate (tc.trust) can be downloaded directly from: Senet TLS Server Certificate
Extract the contents from the Certificate, or copy the value below, and enter the value as the Server CA Certificate (tc.trust).

Source file	PEM formatted contents
Senet tc.trust		`Starts with: -----BEGIN CERTIFICATE-----MIIETjCCAzagAwIBAgINA ... ... omitted contents, use copy certificate button ... Ends with: ... f6q8amaEsybwMbDqKWwIX7eSPY=-----END CERTIFICATE-----`

The Gateway Cert and Gateway Key are not required, and can be left blank.
Save the changes.
Reboot the Base Station.

Screenshot

Unsecured LNS URI

A page will appear showing Basic Station Configuration
Select LNS from the Authentication drop-down menu.
Select 915 (US, AU, AS) from the Region drop-down menu.
Enter the Manufacturer (Base Station) EUI as derived above as the EUI prefix.
Enter ws://ns-gw.senetco.io:6040 as the Server URI value.
A copy of the Server CA Certificate (tc.trust) is not required, and can be left blank.
The Gateway Cert and Gateway Key are not required, and can be left blank.
Save the changes.
Reboot the Base Station.

Screenshot

Verifying Connection to the Senet Network

Upon successful completion, the Base Station status will update to Registered - Active when viewed within the Senet Portal, and the status indicator light will turn green.